MICROBOT MOTOR DRIVER DOWNLOAD

Supply voltage for motors 46Vmax. Add to shopping cart. On this shield the selection of the power source for motor outputs is accomplished by a jumper. All orders after this time will be shipped again from The Easy Motor Controller provides two separate power supplies, one for the motor and the other one for the logic part; the latter can be pulled out through a jumper directly from that of the motor or alternatively from the BEC circuit of the RC receiver. The Driver IC may become very hot when working with current more than 1A.

Uploader: Zolorisar
Date Added: 18 April 2004
File Size: 7.5 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 47243
Price: Free* [*Free Regsitration Required]

Do you need a written offer before ordering? To prevent board damages, all driver lines are diode protected from back EMF. To moror the response to RC commands you also have the calibration function on the receiver signals.

The Easy Motor Controller allows to control the speed and the direction of rotation of a DC motor through three different possible inputs: The Easy Motor Controller provides two separate power supplies, one for the motor and the other one for the logic mootr the latter can be pulled out through notor jumper directly from that of the motor or alternatively from the BEC circuit of the RC receiver.

The maximum supply voltage supported by this board is 30V. Add to shopping cart. Cookies help us deliver our services. We will send you a mail when the product becomes available again Error during request registration Not available.

Cookies help us deliver our services. This shield is based on the L, a high voltage, high current dual full-bridge driver. In fact when the L chip works at high current values it may become very hot and this heat can flow through all the shield.

  HP 6910P FINGERPRINT DRIVER

On this shield it has been included an integrated I2C digital temperature sensor to monitor the shield temperature in order to prevent overtemperature threat.

Maggiori informazioni Read more. The possibility of using two limit microswitches that will act as a protection, interrupting the movement of the motor in the two possible directions when the pressure of the microswitch is detected, completes the functions on the board. Microbot Easy Motor Controller Microbot. The logic of the Dual DC Motor Shield is powered directly from the Arduino board, whereas motor outputs can be powered both from Arduino Vin pin or from external power source, even if it is strongly encouraged to use external power supply.

DC Dual Motor Driver 30V 4A V2

This product is currently not available. By using our services, you agree to our use mohor cookies. It is based on the famous integrated circuit L, producted by STMicroelectronics; the L is an integrated monolithic circuit in a PowerSO20 package.

The sensor is the integrated circuit TCN75A and you can refer to its datasheet to better understanding its communication protocol. This board also provides direction LED indicators for both channels; this is very usefull during setup stage to verify the firmware behaviour also without appling a real motor to the output. We would like to ask you to consider this in your order planning!

Dual DC Motor Shield

The Driver IC may become very hot when working with current more than 1A. It is a high voltage, high current dual fullbridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays,solenoids, DC and stepping motors.

  AE1000 CISCO DRIVER DOWNLOAD

To enable or disable each channel independently of the input signals there are provided two enable inputs E1, E2 positioned on the front of the board; microblt velocity regulation is obtained applying mohor these pins a PWM signal with a 20KHz max.

The maximum supply voltage supported by this board is 46V. This board also provides direction LED indicators for both channels and this is very usefull during setup stage to verify the firmware behaviour; the led indicators work also without appling a real motor to the output. For the I2C communication, there are two different slave addresses selectable through a jumper, and in this way it is possible to use two Easy Motor Controllers on the same serial line, and then control them by using a single external controller.

Supply voltage for motors 46Vmax. Maggiori informazioni Read more. To ensure safely operating condition you can measure the mofor current absorption of each motor; this allow to avoid stall conditions. Moving the jumper from one side to the other the power source can be changed.

By using our services, you agree to our use of cookies. Specifications Supply voltage 7 – 30V Supply current logic 24mA typ. On this shield the selection of the power source for motor outputs is accomplished by a jumper.

View additional product data.